Back to blog
7 min read

Post-Silicon Bring-Up Interview Questions: Lab Debug Scenarios

In a bring-up interview, show a sensible order of operations: check power rails, current, and shorts first, then clocks and resets, then JTAG access such as reading an ID code, then smoke tests and shmoo characterization. For a failing part, isolate silicon, board, and firmware as separate suspects and change one variable at a time.

Practice these questions live in a Design Verification mock interview with a verified engineer. Book a Design Verification mock interview

Post-SiliconBring-UpValidationLab DebugInterview Prep

The chip is back from the fab and sitting in a socket on your bench. You apply power and nothing obvious happens. What do you check first, and in what order? Interviewers for bring-up roles often care less about the right answer than about whether your order of operations makes sense.

This guide draws on public bring-up write-ups from ChipVerify and SoCLabs, a shmoo plot article on Design&Reuse, and boundary scan tutorials from Corelis and Ecrionix. The practice prompts and the lab scenario are ours, not questions reported from any employer.

Why check power first, before everything else?

ChipVerify describes the first step of bring-up as checking each supply rail for the right voltage, checking that current draw is within expected limits, and looking for shorts. It says unexpected current at power-on points to a physical fault, and that no further testing should proceed until the power profile is understood.

If you jump straight to "I would load firmware," you have skipped the step that protects the part and the board. Describe the supply order, bench supply current limits, and what a high idle current would tell you. Our guide to power integrity, decoupling, and IR drop covers the noise side.

Clocks, resets, and the first sign of life

The same source calls a PLL locking to its reference an early milestone, because synchronous logic cannot run without a stable clock. It also points out that reset behavior on silicon can differ from simulation, since real PLL lock time, power-on-reset circuits, and clock edges all influence how blocks come out of reset.

A good answer separates what you observe from what you infer: probe the reference clock and PLL output, check the lock indicator if exposed, and compare reset de-assertion timing against the documented sequence. Our PLL and clocking interview guide covers jitter and loop behavior in more detail.

Why is JTAG usually the first conversation with the chip?

ChipVerify says JTAG is typically the first debug interface used after reset bring-up, and that reading a known register or a device ID is a common smoke test. Ecrionix describes the TAP controller as a 16-state machine driven by TMS and says holding TMS high for five consecutive TCK cycles returns it to Test-Logic-Reset from any state. It describes IDCODE as shifting out a 32-bit identification value, laid out in its example as a 4-bit version, a 16-bit part number, an 11-bit manufacturer code, and a fixed 1 in the lowest bit.

Corelis lists three required IEEE 1149.1 instructions (EXTEST, SAMPLE/PRELOAD, BYPASS) and notes that nearly every new microprocessor includes boundary scan circuitry for testing and in-circuit emulation. A correct ID tells you power, clock, and the TAP path to the die are all working. Garbage or all ones gives you a narrower list of suspects.

SoCLabs notes, in its open nanoSoC reference, that the debug path depends on the design and that the test board can measure power per domain. In an interview, it is fair to ask what debug access the part exposes. Scan background is in our DFT interview guide.

Study plan from the sources

TopicWhat the source saysPractice prompt
Power-onCheck rails, current, and shorts before any other test (ChipVerify)What would you do if idle current is twice the expected value?
Clocks and resetPLL lock and reset timing on silicon can differ from simulation (ChipVerify)How do you tell a missing clock from a stuck reset?
JTAGTMS high for five TCK cycles resets the TAP; IDCODE returns a 32-bit ID (Ecrionix)The ID reads all zeros. What are your first three suspects?
Smoke testsRead known registers, then check UART, SPI, I2C (ChipVerify)What is the smallest test that proves the core is executing?
Shmoo plotsPass/fail map over voltage and frequency, sometimes temperature (Design&Reuse)What would a vertical failure edge suggest to you?
TriageTry to reproduce in RTL simulation to separate RTL bugs from silicon-specific ones (ChipVerify)How do you decide where a failure belongs?

How do you read a shmoo plot?

Design&Reuse explains that a shmoo plot shows which combinations of conditions a part passes or fails, usually with frequency on one axis and voltage on the other, and sometimes temperature as a third variable. It describes a few shapes and what they might suggest. A wall, where failure happens at a certain voltage regardless of frequency, may point to noise coupling, races, or charge sharing. A brick wall, where results change between initializations, may come from registers with no defined reset value. A floor, where the part works fast but fails slow, may suggest leakage or a timing issue.

Treat these as hypotheses, not diagnoses: "That shape makes me suspect X, and here is the measurement that would separate X from Y." ChipVerify places characterization across voltage, temperature, and samples from different lots, along with speed binning, in this stage. For the role boundary between this work and production test, see our comparison of silicon validation and product test engineers.

An illustrative lab scenario

This is a made-up practice scenario, not a reported question. A new SoC boots a small test program at room temperature but hangs about one run in five once the chamber is at high temperature. The same firmware runs fine on a second board.

A reasonable way to talk through it:

  1. Restate the symptom and what is known: failure rate, temperature, board, firmware version, and whether the hang is at the same point each time.
  2. Rule out the bench first: check supply droop and clock quality at the pins on the failing board and compare with the good board.
  3. Swap the part between boards, and swap boards under the same part. This separates silicon from board in one step.
  4. Hold the firmware constant, then vary one thing at a time: voltage, frequency, or temperature, and build a small shmoo around the failing point.
  5. Try to reproduce in simulation or emulation with the failing sequence. If it reproduces, suspect RTL or firmware. If not, a marginal timing path or a power issue becomes more likely.
  6. Say what evidence would change your mind, and what you would hand to design if it looks like silicon.

The point is to isolate silicon, board, and firmware as separate suspects. Our guide on pre-silicon verification versus post-silicon validation frames how those two worlds hand problems to each other, and the SerDes eye diagram guide shows the same evidence-first style on a high speed link.

Prepare one bring-up story

Pick a board or FPGA project, even a small one, where you debugged something at the bench. Explain what you measured, what you ruled out, and what you got wrong. If your experience is mostly simulation, say so. The two week interview plan can help you fit this practice into a short schedule, and you can book a mock interview on MockVise to rehearse talking through a failing part.

Sources: ChipVerify, SoCLabs, Design&Reuse, Corelis, Ecrionix. This article offers general technical preparation guidance, not an official interview process or reported company questions. The scenario is illustrative, and real bring-up procedures differ by company, chip, and lab. Confirm interview details with your recruiter. MockVise is not affiliated with or endorsed by ChipVerify, SoCLabs, Design&Reuse, Corelis, or Ecrionix.

FAQ

Q: What does a JTAG ID read tell you about a new chip? A correct ID tells you power, clock, and the TAP path to the die are all working. Garbage or all ones gives you a narrower list of suspects.

Q: What is a shmoo plot? It is a map of which combinations of conditions a part passes or fails, usually with frequency on one axis and voltage on the other, and sometimes temperature as a third variable.

Q: How do you separate a silicon problem from a board problem? Swap the part between boards, and swap boards under the same part. This separates silicon from board in one step.

Q: Why can reset behavior on silicon differ from simulation? Real PLL lock time, power-on-reset circuits, and clock edges all influence how blocks come out of reset.

Practice with engineers who've run these interviews

Book a 1-on-1 mock interview with verified experts from Intel, NVIDIA, Qualcomm, and Apple. Practice these questions live in a Design Verification mock interview with a verified engineer.

Find a Design Verification expert

Already running these interviews at work? Get paid to run them on MockVise, anonymously and on your own hours. Become an expert